I HAVE A SPECIAL LOVE FOR  OLD PFAFF 130'S .

THEY WERE BUILT IN GERMANY BEFORE AND AFTER WWII . THEY ARE TOUGH AND BEAUTIFUL . YOU CAN SEE THE SPECIAL ATTENTION I GIVE EVERY ONE . I AM A TRAINED PFAFF INDUSTRIAL TECHNICIAN 

BUT HAVE A LOVE FOR ALL OF THE PFAFFS .

=========================

==========next===========

=========================

 

PFAFF 130-50010

WITH UPGRADED MOTOR AND SPECIAL

SPOKED HANDWHEEL

 

NEVER RUN YOUR 130 WITHOUT A CASE BOTTOM OR OUT OF THE CABINET
AS  THIS COULD DAMAGE THE INTERNAL TIMING BELT
AND ALSO IT KEEPS IT FROM WALKING AROUND ON THE TABLE

READY TO SEW

              AVAILABLE NOW !!!!

      $859.00 + $60.00 SHIPPING

           IS $799.00 +$60.00 ON EBAY

THIS IS $140.00 CHEAPER THAN EBAY

BEING FROM THE EARLY 1950'S THERE MAY BE SOME EXTREMELY LITE SMUDGES OR SCRATCHES ,BUT YOU WILL HAVE TO LOOK PRETTY CLOSE TO FIND THEM AS IT IS IN REALLY GREAT CONDITION FOR BEING AROUND 60 YEARS OLD

 

EMBROIDERY ADAPTOR WORKS GREAT

SAVE THE TWIN NEEDLE FOR EXPERTS

Above are a few of the many embroidery stitches it does automatically , will do these in needle L ,CENTER AND RIGHT POSITION . SO YOU CAN SEE THE SAMPLE ABOVE WAS ALL DONE WITH THE NEEDLE IN THE LEFT POSITION , DOES A TOTAL OF 54 DESIGHNS . I USED A NUMBER 11 NEEDLE AS IT WAS ALL PURPOSE THREAD . 

AS YOU CAN SEE IN THE PHOTO ABOVE ,IT COMES READY TO SEW ,WITH ALL 3 MANUALS ,THE PFAFF 130 MANUAL , THE DIAL A STITCH MANUAL , THE 50010 MANUAL AND THE DIAL A STITCH DESIGN WHEEL .

   ORIGINAL BAKELITE HANDWHEEL 

130-50010 ,AWESOME POWER WITH MY UPGRADED 1.5 AMP MOTOR ,THE ORIGINAL WAS THE PFAFF 1.3 AMP AND AFTER 50 OR 60 YEARS HAS WEAKENED ,THIS ONE WAS RETROFITTED TO THE MACHINE ALONG WITH THE SPOKED HANDEHEEL . ALSO COMES WITH THE ORIGINAL ( SMALLER )BAKELITE HANDWHEEL .

IT IS A $165.00 UPGRADE ON THIS WEBSITE AND A $184.00 UPGRADE ON EBAY

THE DARK SPOT IN THE MIDDLE OF THE BED IS JUST A REFLECTION OF THE BLACK PAPER CLIP HOLDING MY WHITE SHEET TO THE WALL

HOW TO USE THE MACHINE :
 
THE MACHINE COMES WITH 3 MANUALS 
1 SHOWS YOU HOW TO USE THE DIAL A STITCH ZIGZAG KNOB
1 SHOWS YOU HOW TO USE THE MACHINE
1 SHOWS YOU HOW TO USE THE 50010 EMBROIDERY ADAPTOR
ALSO INCLUDED IN A PLASTIC ENVELOPE IS A STITCH DESIGN WHEEL
 
THE STITCH DESIGN WHEEL HAS 54 STITCHES ON IT AND  NUMBERS 1 2 AND 3
 
THE DESIGN WHEEL HAS 54 DESIGNS ON THE OTHER SIDE FOR TWIN NEEDLE SEWING
ROTATE THE CENTER TO POINT TO A SPECIFIC STITCH DESIGN USE THE 3 NUMBERS BELOW THE CUT OUT ARROW TO SET THE A AND B LEVERS
 ON TOP OF THE EMBROIDERY ADAPTOR 
LEVER C IS UNDER THE BOTTOM LEFT OF THE ZZ DIAL . 
LEVER C LETS YOU MOVE THE ZZ KNOB DIAGONALLY  FROM R,C,L NEEDLE POSITION
THIS SOUNDS DIFFICULT BUT BECOMES SECOND NATURE .
THE EMBROIDERY A LEVER LETS YOU CHOOSE FROM 6 STITCH DESIGNS
LEVER B LETS YOU CHOOSE FROM SHORT MEDIUM TO LONG DESIGN REPETITIONS
SET THE ZZ KNOB AT THE TOP ( NEEDLE IN FAR LEFT POSITION ) AND IT WILL CLICK AS YOU
MOVE ZIGZAG FROM 0 TO 4 . THERE IS ALSO A MECHANICAL MEMORY AT THE TOP LEFT OF THE ZZ KNOB.
 
IN THE CENTER AND RIGHT POSITIONS THE ZZ KNOB DOESN'T CLICK AND MOVES MORE FREELY.
TO ENGAUGE THE 50010 ASSEMBLY, PULL THE PIN OUT FROM THE BOTTOM OF THE ZZ KNOB 
( DO NOT REMOVE IT  JUST PULL IT OUT A BIT AND CENTER IT BELOW  IN THE SLOT .
NOW TAKE LEVER B OFF OF 0 AND MOVE IT TO 1 ,2 OR 3 . TIGHTEN THE THUMBWHEEL AT THE TOP 
OF THE ZZ KNOB AND YOU ARE GOOD TO GO .
 
IF YOU HAVE THE ZZ KNOB SET TO  ZERO AND ARE JUST DOING STRAIGHT or ZZ STICHING THEN MOVE LEVER B TO ZERO AND UNSCREW THE THUMBWHEEL ( DO NOT REMOVE IT AND DO NOT LOOSE IT AS THEY ARE NOT REPLACEABLE )
SO AS NOT TO LOAD THE MOTOR DOWN

These handwheels are as close as you can get to the originals,I have cut,bored and balanced it as the originals are . These are not like any others you can buy , I pay more for these and it's worth it as the ones from china are not round and wobble .

Comes with Very hard to find original swivel light (These are very delicate bakelight ) .

AND A PAIN TO SHIP :) .

Tensioner and Zigzag Dials are both repainted   (numbers and circles ).

to adjust the upper tension ( above ) before threading the needle 

take the thread in your left hand just before you thread it through the thread take up lever and with the pressor foot down pull the thread through the closed tensioner using your left hand to tighten or loosen the tension ,do not go buy the numbers on the dial , after a while you will be able to sense the correct tension . if it is looping on the underside tighten the tension ( clockwise ) if it is pulling the bottom thread up through the top then loosen the tension knob (counter clockwise ) . thin material requires less tension as thicker material requires more tension .

Remember to adjust the pressor foot tension ( tube on the top front screws in for more tension on thicker materials like leather and screws out for thinner materials . This will keep the pressor foot from coming up with the needle . leave it loose when not sewing as to keep the internal spring from staying compressed .

see the set screw in the bobbin above . You may want to mark where the slot is with a black permanent marker .Only adjust this small screw if the upper tension adjustments fail .JUST TURN IT A QUARTER TURN, if the thread is coming through the top of te material then turn this screw clockwise to tighten the thread ,if it is pulling thr top thread to the bottom then turn the small screw ccw ( loosen ) . Always mark it before you move it so you will know where it was . A little aceitone on a Qtip will remove the mark . Only do this if the upper tension adjustment fails , (bobbin case adjustment should be fine where I set it ) .

Also  includes one of my modified handcranks

sewed 1/4" ( 5 LAYERS ) of upholstery leather as well as 8 layers of denim and 4 layers of webbing as well as the Twin needle . Have a professional try the twin needle first ,you must try it by hand first and find the correct zz needle width .

 

THIS IS WHAT I USE THE MACHINE FOR . I DON'T RECOMMEND TANNED OR TOOLED OR BRIDEL LEATHER ,JUST UPHOLSTERY LEATHER .

THE CASE BOTTOM IS REBUILT AND I EVEN PUT                               NEW FEET ON IT .

I HAVE DESCRIBED THIS MACHINE TO THE BEST OF MY ABILITY , WHAT

YOU SEE IS WHAT YOU GET

Here are my packers . They are eagerly packing your machine and awaiting it's arrival to you .

         END OF LISTING

=======================

<< New text box >>

          BELOW AVAILABLE NOW

        $650.00 + $50.00 SHIPPING

      SELLS FOR $799.00 + $50.00          SHIPPING ON EBAY

NEVER RUN YOUR 130 WITHOUT A CASE BOTTOM OR OUT OF THE CABINET
AS  THIS COULD DAMAGE THE INTERNAL TIMING BELT
AND ALSO IT KEEPS IT FROM WALKING AROUND ON THE TABLE

          NEW PFAFF 130-6

READY TO SEW

THIS 130-6 IS ABSOLUTLY BEAUTIFUL

COMES WITH 1.5 AMP MOTOR UPGRADE AND SPOKED HANDWHEEL

THAT'S $150.00 UPGRADE ,IS $184.00

UPGRADE ON EBAY

 

MY CUSTOMERS LOVE THIS UPGRADE ESPECIALLY

THE 1.5 AMP MOTOR

 

THE ORIGINAL MOTOR WAS ONLY 1.3 AMPS AND HAD BECOME WEAK AS MOST OF THEM DO WITH AGE .THE ORIGINAL SMALL BAKELITE WHEEL IS ALSO INCLUDED

HAS A VERY FEW SMUDGES AND BLEMISHES BUT 

IS AWESOME FOR 60 YEARS OLD

ABOVE IS THE CHECK LIST I MADE FOR IT . 

COMES WITH BOTH MANUALS ALSO AND

A CASE WITH A PULL OUT KICKSTAND ON THE BOTTOM

COMES WITH ORIGINAL PFAFF TIN FULL OF 

ORIGINAL PFAFF ACCESSORIES 

+  3 #18 SCHMETZ GERMAN LEATHER 

NEEDLES AND A PACK OF 4 SMALLER DRITZ 

NEEDLES OF ASSORTED SIZES 

FRONT SHAFT

AND HOOK

REAR SHAFT

WITH TIMING

BELT

BOTH TENSION AND ZIGZAG KNOBS HAVE EVEN BEEN REPAINTED WITH TOOTHPICS (MOST OTHER SELLERS DON'T DO THIS ) , NOW AS FOR THE ZZ KNOB ,IT DOES L, C AND RIGHT STITCHES .

JUST SET THE ZZ WIDTH IN THE MIDDLE OF THE WIDTH RANGE  ,THEN PUSH THE LEVER ON THE LOWER LEFT ALL OF THE WAY IN THEN MOVE THE WHOLE ZZ KNOB ,IT MOVES DIAGONALLY FROM LOWER RIGHT TO UPPER LEFT .

YOU MAY HAVE TO CURL THE FINGERS OF YOUR RIGHT HAND AROUND THE REAR SPOOL PIN AND PUSH ON THE ZIGZAG KNOB WITH YOUR RIGHT THUMB TO MOVE IT BACK TO THE UPPER LEFT POSITION.

ONCE YOU DO THIS SEVERAL TIMES IT SHOULD BECOME SECOND NATURE .

SET THE NEEDLE POSITION WHERE YOU WANT IT THEN RELEASE THE LEVER AND SET THE ZIGZAG WIDTH TO WHERE YOU WANT IT .

SHE REALLY SEWS GREAT

ABOVE IS THE SPOKED HANDWHEEL AND NEW 1.5 AMP MOTOR DRILLED 

AND THREADED TO FIT THE ORIGINAL MOTOR BRACKET

 

 

MANUALS

ALL SAMPLES

THIN TO THICK MATERIAL

THIN,8 LAYERS OF DENIM ,5 LAYERS 1/4" OF UPHOLSTERY LEATHER , BROWN FAUX LEATHER 4 LAYERS ,4 LAYERS OF WEBBING

1/4" OF LEATHER.

THE LITTLE SPECS YOU SEE ON THE BED ARE JUST LITTLE CRUMBS OF THE RED LEATHER .THESE ARE LAYING ON A BLACK TEE SHIRT , NOT THE BLACK BED OF THE MACHINE

LIGHT COTTON MATERIAL ON LEFT 

8 LAYERS OF DENIM ON RIGHT

SERIAL NUMBER

 

IT WAS MADE 

BETWEEN

1953/1954

ORIGINAL HANDWHEEL

I HAVE DESCRIBED THIS MACHINE TO THE BEST OF MY ABILITY , WHAT

YOU SEE IS WHAT YOU GET

Here are my packers . They are eagerly packing your machine and awaiting it's safe arrival to you .

THIS IS THE END OF THIS LISTING

=================================

 

 

YOU CAN CONTACT ME AT lazerman1@hotmail.com

================================

==============next==============

================================

ALL ORDERS HAVE A 30% RESTOCKING FEE , ESPECIALLY THE HANDWHEELS

Welcome to ZEUSMACHINES.

1.5 AMP MOTOR UPGRADE

1.5 AMP MOTOR UPGRADE WITH SPOKED WHEEL . THIS WHEEL IS NOT ONE OF THOSE CHEAP CHINESE WHEELS THAT WOBBLES BADLY.

THEY ARE VERY CLOSE TO THE OLD ORIGINALS WHICH WERE NOT BALANCED PERFECTLY BUT WERE VERY CLOSE. 

PRICE IS $150.00 + $12.00 shipping

30%RESTOCKING FEE

 

some customers complain about the mild grinding I do between the spokes of the handwheel (It's the only way I know to balance them) I,ll only do grinding in between 2 spokes maybe in 1 or 2 spots.  always put your pfaff 130 or 30 or 130-50010 in a case or cabinet so it doesn't walk around or more importantly so the internal timing belt is NOT DAMAGED .

===========next============

EMAIL ME AT lazerman1@hotmail.com 

MY SPOKED WHEELS ARE TURNED ON MY LATHE TO SHAVE THE BOBBIN WHEEL TRACK DOWN SO YOU CAN USE A REGULAR BOBBIN WINDING TIRE WITH THEM INSTEAD OF USING ONE OF THOSE TINY HARD TO PUSH IN ONES .

 THE HOLE FOR THE SHAFT HAS TO BE BORED OUT TOO .

THIS IS THE SAME WHEEL SHOWN ABOVE WITH THE NEW MOTOR

 

PRICE IS $54.99 would be more on ebay

JUST THE 1.5 AMP MOTOR IS $115.00 + $15.00 SHIPPING

BOTH MOTOR AND SPOKED HANDWHEEL ARE MODIFIED FOR THE PFAFF 130

SPOKED HANDWHEELS ARE $54.99 + $10.00 SHIPPING

HANDCRANKS ARE $35.00 EACH + $10.00 SHIPPING .

30% RESTOCKING FEE 

IF YOU ARE A VERY PICKY PERSON ,DO MOT ORDER THE SPOKED HANDWHEEL . THESE ARE WAY BETTER THAN THE CHEAP CHINESE ONES WHICH ARE BADLY OUT OF ROUND AND DON'T EVEN HAVE THE HOLE DRILLED IN THE PERFECT CENTER . THESE ARE MADE TO GET WORK DONE BUT IF YOU ARE GOING TO RETURN IT BECAUSE THEY ARE NOT PURFECT THEN DO NOT ORDER THE SPOKED HANDWHEEL . THEY DO HAVE ROUGH PLACES BETWEEN THE SPOKES . I DO THE BEST I CAN REMACHINING ,BORING THE HOLE BIGGER AND CUTTIND DOWN THE BOBBIN TIRE TRACK . SOMETIMES I EVEN BALANCE THEM BUT IF YOU DONT WANT TO SEE THE GRINDING BETWEEN THE SPOKES THEN ORDER ONE UNBALANCED ,LET MW KNOW IF YOU WANT IT BALANCED WHEN YOU ORDER IT . AGAIN, THESE ARE WAY BETTER THAN THE CHEAP ONES MADE IN CHINA ,THEY COME FROM A FOUNDRY IN TAIWAN AND ARE NOT CHEAP . AGAIN THEY ARE NOT PERFECT BUT I DO THE BEST I CAN WITH WHAT I HAVE TO WORK WITH ..

=========================

( SOLD FOR $899.00)

=======================

BEAUTIFUL PFAFF 130-6 WITH SPOKED HANDWHEED . PAINTED METALLIC

RUBY RED .

** !!!! JUST EMAIL ME AT lazerman1@hotmail.com !!!! **

MY EMAIL IS   www.lazerman1@hotmail.com

I HAVE BEEN IN BUSINESS FOR 16 YEARS

I CAN INVOICE YOU THROUGH PAYPAL .

BRAND NEW PFAFF 130-6 WITH HOME MADE WOOD CASE.I'M THE ONLY ONE THAT DOES THESE IN DIFFERENT COLORS AT CHRISTMAS TIME .THIS MAY BE MY VERY LAST ONE .

 

WILL ARRIVE IN THIS

HOME BUILT CASE ,

BUSTED MY ASS BUILDING

TWO OF THESE .

EVEN COMES WITH KICKSTAND

NEW RUBBER FEET AND PLENTY OF FELT .

WAS ON EBAY FOR($899.00)

IS $200.00 CHEAPER HERE .

( $599.00 )     + $50.00

SHIPPING IN

THE LOWE 48 STATES . MORE FOR ANYWHERE ELSE IN THE USA .

YOU MUST REMOVE THE MOTOR TO USE THE HANDCRANK

SEWED OVER 15/32 OF LEATHER (3 PIECES)

4 PIECES OF WEBBING 4 LAYERS OF YELLOW COTTON (EASY PEASY)AND 3 LAYERS OF LEATHER.  I DON'T RECOMMEND ANYTHING OVER 1/4" UNDER THE FOOT .

THATS OVER 14 OUNCES OF DENIM

INTERNAL TIMING BELT LOOKS FINE AS DOES EVERYTHING ELSE UNDER THE MACHINE

CASE MADE FOR MY PFAFF 130

DO NOT LIFT MACHINE WITH CASE HANDEL , THIS IS STRICTLY FOR REMOVING THE CASE LID

COMES WITH CASE MANUALS AND FULL ACCESSORIES

HAS A SOLID IRON ZZ GEAR,THEN REBUILT THE FRONTEND,ZIGZAG AND BOBBIN WINDER .

SEE IT ALL ON EBAY UNDER ZEUSMACHINES .

=================================

 !!  SOLD !! PRICE WAS $850.00 + 50.00 SHIPPING

 

METALLIC EMERALD GREEN

BRAND NEW PFAFF 130-6 WITH HOME MADE WOOD CASE.

 

I'M THE ONLY ONE THAT DOES THESE IN DIFFERENT COLORS AT CHRISTMAS TIME,

 

THIS ONE IS A BEAUTIFULL EMERALD METALLIC GREEN

THIS IS MY NEWEST PHOTO SHOWING THE HAND CRANK

COMES WITH ONE OF MY 1.5 AMP UPGRADED MOTORS

BEAUTIFUL EMERALD METALLIC GREEN

DO NOT LIFT MACHINE USING CASE HANDLE , THIS IS STRICTLY FOR JUST REMOVING THE COVER

ABOVE PHOTO HAD LESS POWERFUL OLDER MOTOR ON IT

 !! ABOVE SOLD PRICE WAS $850.00 + $50.00 SHIPPING !!

=============================

IN REALLY NEW CONDITION

BROTHER SUPERSTREAMLINER

STRAIGHT STITCH MACHINE

 

I MEAN IT IS JUST LIKE BRAND NEW WITH ALL 3 TAGS LIKE IT WAS NEVER USED .

IS LISTED FOR $250.00 ON EBAY .

 

SOLD $399.00 + 50.00 SHIPPING ( !! SOLD !! )

 

** !!!! JUST EMAIL ME AT lazerman1@hotmail.com !!!! **

COMES WITH  MANUAL ACCESSORIES AND EVEN ORIGINAL CASE IN EXTREMELY GOOD CONDITION.

 

ALSO HAS MANY ACCESSORIES

SERIOUSLY IT LOOKS LIKE IT WAS NEVER USED

 I FORGOT TO PUT A NEW BOBBIN WINDER TIRE ON IT . I WILL DO THAT AS SOON AS I FINISH THIS AD .

WHAT A PEACH AND WHAT A PRETTY COLOR. I

WASN'T GOING TO SELL HER BUT SHE HAS BEEN IN THE CASE IN THE CLOSET FOR 10 YEARS .

WAS PROBABLY MADE IN THE MID 1960'S

COMES WITH ACCESSORIES AMD MANUAL AND REALLY NICE LIKE NEW  SOLID

WOOD BROTHER CASE .

SEWED OVER  1/4" HEAVY DENIM THATS 10 OR 11 LAYERS AROUND 14/15 OUNCES .

DOES A REALLY GREAT STITCH

 

=================================

=================================

THESE ARE AWESOME MOTORS . I REDRILL THEM AFTER DISASSEMBLING THEM SO THEY WILL FIT THE PFAFF 130 MOTOR BRACKET .

CHEAP ALPHASEW MOTOR ON LEFT,MY HEAVY DUTY 1.5 MOTOR ON RIGHT. THE CHEAP ALPHASEW MOTOR WILL SMOKE BADLY IF PUT ON A 130. MINE WILL NOT ....

YOU MUST HAVE AN ORIGINAL PFAFF 130 MOTOR BRACKET. THIS MOTOR IS ON THE RIGHT SIDE IN THE PHOTO. THE CHEAP CHINA MADE 1.5 AMP IS ON THE LEFT. THIS WILL SMOKE IF MOUNTED ON A PFAFF 130..MY MOTORS ARE $115.00 + $12.00 SHIPPING

===============================

THIS IS THE SAME WHEEL SHOWN AT THE TOP WITH THE NEW MOTOR

FEEL FREE TO CLICK THROUGH THE PAGES AT THE TOP

Contact Us

ZEUSMACHINES

 

Cartersville, GA. 30120

 

lazerman1@hotmail.com

 

News

We have recently updated our website to better represent who we are as a company and what we can do for you!

Get Social With Us

Recommend this page on:

Print Print | Sitemap
ZEUSMACHNES

E-mail